prop protector, prop protector line cutter, line cutters, boat shaft line cutters, propellers line cutters, propeller line cutter, boat propeller line cutter, line cutter, prop line cutter http://www.getaprop.com/content-categories/cat-391_876/prop_protector_metric.html Sat, 26 May 2012 14:20:01 -0500 en Clamp on Type... 150mm Blade, 45-60mm shafts... Supplied as an assembly that is split into two halves along the longitudinal axis so that it can be installed on the shaft without removing the propeller. The width is 0.67" (17mm). A gap of 0.9" (23mm) is sufficient; this includes 1/4" (6mm) of space for water to circulate to the shaft bearing. It is clamped onto the shaft by two Allen screws and is also fixed by a set screw that locates into a small drill dimple made in the shaft. Blade Diameter:150mm Unit Width:30mm Min. Gap:42mm http://www.getaprop.com/content-product_info/product_id-6928/prop_protector_150mm.html http://www.getaprop.com/images/products/no1[1][2].JPG http://www.getaprop.com/content-product_info/product_id-6928/prop_protector_150mm.html Clamp on Type... 127mm Blade, 45-50mm shafts... Supplied as an assembly that is split into two halves along the longitudinal axis so that it can be installed on the shaft without removing the propeller. The width is 0.67" (17mm). A gap of 0.9" (23mm) is sufficient; this includes 1/4" (6mm) of space for water to circulate to the shaft bearing. It is clamped onto the shaft by two Allen screws and is also fixed by a set screw that locates into a small drill dimple made in the shaft. Blade Diameter:127mm Unit Width:17mm Min. Gap:23mm http://www.getaprop.com/content-product_info/product_id-6926/prop_protector_127mm.html http://www.getaprop.com/images/products/no1[1][2].JPG http://www.getaprop.com/content-product_info/product_id-6926/prop_protector_127mm.html Slide on Type... 120mm Blade, 45-50mm shafts... Manufactured in one piece with a width of only 0.47" (12mm), it is designed for installations where the gap between the propeller and the shaft bearing is small. A gap of 0.7" (18mm) is sufficient; this includes 1/4" (6mm) of space for water to circulate to the shaft bearing. It simply slides onto the shaft after the propeller has been removed and is secured with a set screw that locates into a small drill dimple made in the shaft. Blade Diameter:120mm Unit Width:12mm Min. Gap:18mm http://www.getaprop.com/content-product_info/product_id-6921/prop_protector_120mm.html http://www.getaprop.com/images/products/no2[1][1].JPG http://www.getaprop.com/content-product_info/product_id-6921/prop_protector_120mm.html Clamp on Type... 116mm Blade, 55-60mm shafts... Supplied as an assembly that is split into two halves along the longitudinal axis so that it can be installed on the shaft without removing the propeller. The width is 0.67" (17mm). A gap of 0.9" (23mm) is sufficient; this includes 1/4" (6mm) of space for water to circulate to the shaft bearing. It is clamped onto the shaft by two Allen screws and is also fixed by a set screw that locates into a small drill dimple made in the shaft. Blade Diameter:116mm Unit Width:22mm Min. Gap:32mm http://www.getaprop.com/content-product_info/product_id-6927/prop_protector_116mm.html http://www.getaprop.com/images/products/no1[1][2].JPG http://www.getaprop.com/content-product_info/product_id-6927/prop_protector_116mm.html Clamp on Type... 105mm Blade, 45-50mm shafts... Supplied as an assembly that is split into two halves along the longitudinal axis so that it can be installed on the shaft without removing the propeller. The width is 0.67" (17mm). A gap of 0.9" (23mm) is sufficient; this includes 1/4" (6mm) of space for water to circulate to the shaft bearing. It is clamped onto the shaft by two Allen screws and is also fixed by a set screw that locates into a small drill dimple made in the shaft. Blade Diameter:105mm Unit Width:17mm Min. Gap:23mm http://www.getaprop.com/content-product_info/product_id-6925/prop_protector_105mm.html http://www.getaprop.com/images/products/no1[1][2].JPG http://www.getaprop.com/content-product_info/product_id-6925/prop_protector_105mm.html Slide on Type... 100mm Blade, 30-40mm shafts... Manufactured in one piece with a width of only 0.47" (12mm), it is designed for installations where the gap between the propeller and the shaft bearing is small. A gap of 0.7" (18mm) is sufficient; this includes 1/4" (6mm) of space for water to circulate to the shaft bearing. It simply slides onto the shaft after the propeller has been removed and is secured with a set screw that locates into a small drill dimple made in the shaft. Blade Diameter:100mm Unit Width:12mm Min. Gap:18mm http://www.getaprop.com/content-product_info/product_id-6920/prop_protector_100mm.html http://www.getaprop.com/images/products/no2[1][1].JPG http://www.getaprop.com/content-product_info/product_id-6920/prop_protector_100mm.html Slide on Type... 80mm Blade, 20-30mm shafts... Manufactured in one piece with a width of only 0.47" (12mm), it is designed for installations where the gap between the propeller and the shaft bearing is small. A gap of 0.7" (18mm) is sufficient; this includes 1/4" (6mm) of space for water to circulate to the shaft bearing. It simply slides onto the shaft after the propeller has been removed and is secured with a set screw that locates into a small drill dimple made in the shaft. Blade Diameter:80mm Unit Width:12mm Min. Gap:18mm http://www.getaprop.com/content-product_info/product_id-6919/prop_protector_80mm.html http://www.getaprop.com/images/products/no2[1][1].JPG http://www.getaprop.com/content-product_info/product_id-6919/prop_protector_80mm.html Clamp on Type... 95mm Blade, 35-40mm shafts... Supplied as an assembly that is split into two halves along the longitudinal axis so that it can be installed on the shaft without removing the propeller. The width is 0.67" (17mm). A gap of 0.9" (23mm) is sufficient; this includes 1/4" (6mm) of space for water to circulate to the shaft bearing. It is clamped onto the shaft by two Allen screws and is also fixed by a set screw that locates into a small drill dimple made in the shaft. Blade Diameter:95mm Unit Width:17mm Min. Gap:23mm http://www.getaprop.com/content-product_info/product_id-6924/prop_protector_95mm.html http://www.getaprop.com/images/products/no1[1][2].JPG http://www.getaprop.com/content-product_info/product_id-6924/prop_protector_95mm.html Clamp on Type... 85mm Blade, 30mm shafts... Supplied as an assembly that is split into two halves along the longitudinal axis so that it can be installed on the shaft without removing the propeller. The width is 0.67" (17mm). A gap of 0.9" (23mm) is sufficient; this includes 1/4" (6mm) of space for water to circulate to the shaft bearing. It is clamped onto the shaft by two Allen screws and is also fixed by a set screw that locates into a small drill dimple made in the shaft. Blade Diameter:85mm Unit Width:17mm Min. Gap:23mm http://www.getaprop.com/content-product_info/product_id-6923/prop_protector_85mm.html http://www.getaprop.com/images/products/no1[1][2].JPG http://www.getaprop.com/content-product_info/product_id-6923/prop_protector_85mm.html Clamp on Type... 80mm Blade, 20-25mm shafts... Supplied as an assembly that is split into two halves along the longitudinal axis so that it can be installed on the shaft without removing the propeller. The width is 0.67" (17mm). A gap of 0.9" (23mm) is sufficient; this includes 1/4" (6mm) of space for water to circulate to the shaft bearing. It is clamped onto the shaft by two Allen screws and is also fixed by a set screw that locates into a small drill dimple made in the shaft Blade Diameter:80mm Unit Width:17mm Min. Gap:23mm http://www.getaprop.com/content-product_info/product_id-6922/prop_protector_80mm.html http://www.getaprop.com/images/products/no1[1][2].JPG http://www.getaprop.com/content-product_info/product_id-6922/prop_protector_80mm.html Clamp on Type... 190mm Blade, 65-100mm shafts... Supplied as an assembly that is split into two halves along the longitudinal axis so that it can be installed on the shaft without removing the propeller. The width is 0.67" (17mm). A gap of 0.9" (23mm) is sufficient; this includes 1/4" (6mm) of space for water to circulate to the shaft bearing. It is clamped onto the shaft by two Allen screws and is also fixed by a set screw that locates into a small drill dimple made in the shaft. Blade Diameter:190mm Unit Width:33mm Min. Gap:45mm http://www.getaprop.com/content-product_info/product_id-6929/prop_protector_190mm.html http://www.getaprop.com/images/products/no1[1][2].JPG http://www.getaprop.com/content-product_info/product_id-6929/prop_protector_190mm.html